Where are the jack points on an '08

**SoCal Rebell** · July 19th, 2008, 11:09 PM

Particuarly the ACR (if there is any difference), the frame rails are so far towards the middle of the car I cannot get the jack to it. The Gen2 frame rails were much closer to the outside, had a Gen2 low profile jack also.

Monzsta · July 20th, 2008, 08:19 AM

There should be a protrusion behind the front wheel and ahead of the rear wheel. Looks like a small piece of angle iron.

**SoCal Rebell** · July 20th, 2008, 01:46 PM

Quote:

Originally Posted by Monzsta

There should be a protrusion behind the front wheel and ahead of the rear wheel. Looks like a small piece of angle iron.

Not there, I see 'em on the Gen2's but not Gen4's.

DEVILDOG · July 20th, 2008, 01:49 PM

Learn to read then check the owner's manual.

**SoCal Rebell** · July 20th, 2008, 03:00 PM

Quote:

Originally Posted by DEVILDOG

Learn to read then check the owner's manual.

Learn to shut you fucking mouth you idiot on shit you know nothing about.

.

Westxsrt10 · July 20th, 2008, 03:04 PM

Quote:

Originally Posted by Monzsta

There should be a protrusion behind the front wheel and ahead of the rear wheel. Looks like a small piece of angle iron.

My 08 has the angle iron protrusions as stated above. I also use them as tie-down points.

Monzsta · July 20th, 2008, 03:10 PM

It's possible the ACR doesn't have them. Any one else have an ACR yet?

**sundiego** · July 20th, 2008, 03:15 PM

Quote:

Originally Posted by SoCal Rebell

Particuarly the ACR (if there is any difference), the frame rails are so far towards the middle of the car I cannot get the jack to it. The Gen2 frame rails were much closer to the outside, had a Gen2 low profile jack also.

Ron, the front Jacking point is about 8" in from the side immediately behind the wheel wheel. It is a V shaped piece of metal about an inch and a half long, with the bottom of the v down, and the open section pointing towards the front. At the back, same thing, but about a foot forward of the wheel well. I find them easier to get at than the Gen 2.

**Mr. Hollywood** · July 20th, 2008, 04:28 PM

Unless the ACR is different...think of nipples Ron. One behind each front wheel about 8" inboard. And then another in front of each rear wheel.

Nipples...think Nipples.

**sundiego** · July 20th, 2008, 04:39 PM

Who'da thought porn Ron would have to ask a question about jacking?

REDSLED · July 20th, 2008, 05:04 PM

Quote:

Originally Posted by sundiego

Who'da thought porn Ron would have to ask a question about jacking?

Here you go Ron. Think this is David's car actually.
- VCA Buttonwillow 2008-02-23/VCA Buttonwillow 2008-02-23-15

**sundiego** · July 20th, 2008, 05:19 PM

**SoCal Rebell** · July 20th, 2008, 05:28 PM

Haha, thanks guys, with all the sheet metal covering for aero I couldn't find the nipples

Sgt. Snatch · July 20th, 2008, 07:20 PM

Quote:

Originally Posted by DEVILDOG

Learn to read then check the owner's manual.

[ ] +20

[ ] -20

[x] -20 and add to ignore list.

**SoCal Rebell** · July 20th, 2008, 08:29 PM

Quote:

Originally Posted by Mr. Hollywood

Unless the ACR is different...think of nipples Ron. One behind each front wheel about 8" inboard. And then another in front of each rear wheel.

Nipples...think Nipples.

Kelly, should I throw ice water on the car first?

.

**vettetr** · July 20th, 2008, 08:41 PM

Ron, Did ya pull the trigger on an '08?

**sundiego** · July 20th, 2008, 09:46 PM

Yes, he pulled it for Rocman.

**Rocman** · July 20th, 2008, 09:51 PM

Quote:

Originally Posted by sundiego

Yes, he pulled it for Rocman.

twinturbo3150 · July 20th, 2008, 10:32 PM

Quote:

Originally Posted by SoCal Rebell

Kelly, should I throw ice water on the car first?

.

fuck the ice water get a fluffer like Taylor Wayne that should do the trick.

Boxer12 · July 21st, 2008, 03:47 PM

sometimes its better to use the hands and feel for such things, rather than the eyes...esp when covered up!